MATERIAL SAFETY
DATA SHEET
3M Center
St. Paul, Minnesota
55144-1000
1-800-364-3577 or (651) 737-6501 (24 hours)
Copyright, 2001, Minnesota Mining and Manufacturing Company.
All rights reserved. Copying and/or downloading of this
information for the purpose of properly utilizing 3M products
is allowed provided that:
1) the information is copied in full with no changes unless
prior agreement is obtained from 3M, and
2) neither the copy nor the original is resold or otherwise
distributed with the intention of earning a profit thereon.
This material safety data sheet (MSDS) is provided as a courtesy
in response to a customer request. This product is not regulated
under, and a MSDS is not required for this product by the OSHA
Hazard Communication Standard (29 CFR 1910.1200) because, when
used as recommended or under ordinary conditions, it should not
present a health and safety hazard. However, use or processing
of the product not in accordance with the product's
recommendations or not under ordinary conditions may affect the
performance of the product and may present potential health and
safety hazards.
DIVISION: COMMERCIAL GRAPHICS
TRADE NAME:
SCOTCHCAL BRAND FILM SERIES 7725
ISSUED: December 10, 2001
SUPERSEDES: August 16, 1999
DOCUMENT: 11-6727-9
1. INGREDIENT C.A.S. NO. PERCENT
ADHESIVE COATED PIGMENTED POLYVINYL
CHLORIDE FILM WITH LINER.............. Mixture 100.0
Note: Some pigments may contain lead compounds, e.g. lead chromate
(CAS No. 7758-97-6).
2. PHYSICAL DATA
BOILING POINT:................. N/A
VAPOR PRESSURE:................ N/A
VAPOR DENSITY:................. N/A
EVAPORATION RATE:.............. N/A
SOLUBILITY IN WATER:........... nil
SPECIFIC GRAVITY:.............. N/D
PERCENT VOLATILE:.............. N/A
pH:............................ N/A
VISCOSITY:..................... N/A
MELTING POINT:................. N/D APPEARANCE
AND ODOR:
Adhesive coated film, pigmented, slight odor
3. FIRE AND EXPLOSION HAZARD
DATA
FLASH POINT:................... N/A
FLAMMABLE LIMITS - LEL:........ N/A
FLAMMABLE LIMITS - UEL:........ N/A
AUTOIGNITION TEMPERATURE:...... N/D
EXTINGUISHING MEDIA:
Water spray, Carbon dioxide, Dry chemical, Foam
SPECIAL FIRE FIGHTING PROCEDURES:
Wear full protective clothing, including helmet, self-contained,
positive pressure or pressure demand breathing apparatus, bunker coat
and pants, bands around arms, waist and legs, face mask, and
protective covering for exposed areas of the head.
UNUSUAL FIRE AND EXPLOSION HAZARDS:
See Hazardous Decomposition section for products of combustion.
NFPA HAZARD CODES: HEALTH: 2 FIRE: 1 REACTIVITY: 0
UNUSUAL REACTION HAZARD: none
OSHA FIRE HAZARD CLASS: Not applicable
4. REACTIVITY DATA
STABILITY: Stable
INCOMPATIBILITY - MATERIALS/CONDITIONS TO AVOID:
None known.
HAZARDOUS POLYMERIZATION: Hazardous polymerization will not occur.
HAZARDOUS DECOMPOSITION PRODUCTS:
Carbon Monoxide and Carbon Dioxide, Hydrogen Chloride.
5. ENVIRONMENTAL INFORMATION
SPILL RESPONSE:
Not applicable.
RECOMMENDED DISPOSAL:
Dispose of large quantities in a sanitary landfill. Disposal
alternative: Incinerate in an industrial or commercial facility.
ENVIRONMENTAL DATA:
Not determined.
REGULATORY INFORMATION:
Volatile Organic Compounds: N/A.
VOC Less H2O & Exempt Solvents: N/A.
This substance does not leach metals or other RCRA (Resource
Conservation and Recovery Act) listed TCLP (Toxic Characteristic
Leaching Procedure) hazardous substances at concentrations that would
make the product a hazardous waste. Since regulations vary, consult
applicable regulations or authorities before disposal. U.S. EPA
Hazardous Waste Number = None (Not U.S. EPA Hazardous).
Note: TCLP statement is based on testing of similar films.
EPCRA HAZARD CLASS:
FIRE HAZARD: No PRESSURE: No REACTIVITY: No ACUTE: No CHRONIC: No
6. SUGGESTED FIRST AID
EYE CONTACT:
No need for first aid is anticipated.
SKIN CONTACT:
No need for first aid is anticipated.
INHALATION:
No need for first aid is anticipated. If signs/symptoms occur,
remove person to fresh air. If signs/symptoms continue, call a
physician.
IF SWALLOWED:
No need for first aid is anticipated.
7. PRECAUTIONARY INFORMATION
EYE PROTECTION:
Not applicable.
SKIN PROTECTION:
Not applicable.
RECOMMENDED VENTILATION:
Use in a well-ventilated area.
RESPIRATORY PROTECTION:
Not applicable.
PREVENTION OF ACCIDENTAL INGESTION:
Not applicable.
RECOMMENDED STORAGE:
Store out of direct sunlight. Keep container dry.
Store at a temperature of 100 degrees Fahrenheit or less.
FIRE AND EXPLOSION AVOIDANCE:
Not applicable.
EXPOSURE LIMITS
INGREDIENT VALUE UNIT TYPE AUTH SKIN*
ADHESIVE COATED PIGMENTED
POLYVINYL CHLORIDE FILM WITH LINER. NONE NONE NONE NONE
* SKIN NOTATION: Listed substances indicated with 'Y' under SKIN refer
to
the potential contribution to the overall exposure by the cutaneous
route
including mucous membrane and eye, either by airborne or, more particularly,
by direct contact with the substance. Vehicles can alter skin absorption.
SOURCE OF EXPOSURE LIMIT DATA:
- NONE: None Established
8. HEALTH HAZARD DATA
EYE
CONTACT:
Eye contact is not expected to occur during normal use of the
product. SKIN CONTACT:
No adverse health effects are expected from skin contact.
INHALATION:
The odor associated with these films, which is common
with vinyl materials, is due to low level residual odor from the
manufacturing process. The odor is strongest when a new box is opened
or if the films are used in a room without adequate ventilation.
This
odor has no adverse health effects; however, some people may
initially find the odor objectionable and may even feel nauseated
from it.
IF SWALLOWED:
Ingestion is not a likely route of exposure to this product.
OTHER HEALTH HAZARD INFORMATION:
This product, when used under reasonable conditions or in accordance
with the 3M directions for use, should not present a health and
safety hazard. However, use or processing of the product in a manner
not in accordance with the product's directions for use may affect
the performance of the product and may present potential health
and
safety hazards.
Abbreviations: N/D - Not Determined
N/A - Not Applicable CA - Approximately
The information in this Material Safety
Data Sheet (MSDS) is believed to
be correct as of the date issued. 3M MAKES NO WARRANTIES, EXPRESSED
OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF
PERFORMANCE OR USAGE OF TRADE. User is responsible for determining
whether the 3M product is fit for a particular purpose and suitable
for
user's method of use or application. Given the variety of factors
that
can affect the use and application of a 3M product, some of which
are
uniquely within the user's knowledge and control, it is essential
that
the user evaluate the 3M product to determine whether it is fit for
a
particular purpose and suitable for user's method of use or application.
3M provides information in electronic form as a service to its customers.
Due to the remote possibility that electronic transfer may have resulted
in errors, omissions or alterations in this information, 3M makes
no
representations as to its completeness or accuracy. In addition,
information obtained from a database may not be as current as the
information in the MSDS available directly from 3M. |
